The retirement of an ageing belt press gave Sunbury Wastewater Treatment Plant in Ohio, USA, an opportunity to reassess its sludge dewatering process and select equipment better suited to the plant’s current needs.

Rather than investing in another belt press, the plant opted for an ESMIL sludge dewatering system equipped with an MDQ-504(3) Multi-Disc Screw Press.

The new, fully automated system was commissioned this summer. Since then, sludge dewatering at Sunbury WWTP has become more efficient, with less operator involvement required for day-to-day operation.

Operational Limitations of Belt Filter Presses

Belt filter presses are among the most widely used types of sludge dewatering equipment, but they come with certain operational limitations. To maintain effective filtration, the belts require regular washing, resulting in significant water consumption and associated costs.

These presses also require regular checks of belt alignment and tension, along with routine maintenance, increasing the workload for treatment plant operators.

Multi-Disc Screw Press as an Alternative to Belt Filter Presses

Compared with belt filter presses, multi-disc screw press technology enables continuous, automated sludge dewatering with significantly less operator involvement.

The MDQ press’s low-speed design and self-cleaning filtration surface ensure stable operation without the need for intensive washing. Only periodic rinsing is required, helping to reduce water consumption and maintenance requirements.

In addition, the automatic control system coordinates the entire dewatering process, simplifying day-to-day operations for plant staff.

ESMIL MDQ Sludge Dewatering System with Expansion Capability

The system supplied by ESMIL to Sunbury Wastewater Treatment Plant includes an MDQ-504(3) Multi-Disc Screw Press, two screw conveyors for transporting dewatered sludge and a control system.

The MDQ press is equipped with three dewatering drums, providing sufficient capacity to meet the plant’s current needs. However, the unit has been designed to accommodate a fourth drum within the existing frame if the volume of sludge requiring dewatering increases. This will allow the plant to increase its dewatering capacity without replacing the press with a larger model or undertaking extensive modifications to the installation.

This approach allows the plant to align its initial capital expenditure (CAPEX) with its current requirements while retaining the flexibility to expand the system in the future.

Operating Performance Achieved During Commissioning

During commissioning of the MDQ Multi-Disc Screw Press, the dewatered sludge achieved a dry solids content of 20-23%, an excellent result under the plant’s operating conditions.

The average sludge feed rate is currently approximately 13.6 m³/h, meaning the MDQ press is operating well below its full capacity. This is because only one pump is currently used to feed sludge to the press. The plant plans to install a second pump in the future, allowing it to increase the feed rate and make greater use of the capacity provided by the three installed dewatering drums.

Lower Operating Costs and Reduced Maintenance Requirements

The MDQ Multi-Disc Screw Press consumes less energy and wash water than belt filter presses, helping to reduce operating costs at Sunbury Wastewater Treatment Plant.

Lower operating and maintenance requirements also mean less time spent on routine tasks associated with the press. This allows operators to focus on other aspects of running the treatment plant.

Summary

By replacing its ageing belt filter press with the ESMIL MDQ dewatering system, Sunbury Wastewater Treatment Plant has not only modernised its sludge dewatering process but also simplified day-to-day operations and reduced operating costs.

The new system achieves a high dry solids content in the dewatered sludge with minimal operator involvement. Importantly, it has also been designed for future expansion, allowing the plant to increase its dewatering capacity as sludge volumes grow without having to replace the entire press.

Esmil Group

Esmil Group stands as a premier global manufacturer, crafting cutting-edge equipment for wastewater treatment and sludge dewatering. Additionally, we specialize in delivering advanced membrane systems tailored to various industries.

EU Flag Esmil Group

Equipment for Wastewater Treatment & Sludge Dewatering.

EU Flag Esmil America

Equipment for Sludge Dewatering in the USA.

EU Flag Esmil Process Systems

Membrane Systems.